Installation Procedures
Required Tools:
- Adjustable wrench set
- Digital multimeter
- Torx screwdriver set
- Nut driver set
- Level gauge
- Pressure gauge
Professional Installation Steps
- Site Preparation: Verify location meets clearance requirements and has adequate structural support for unit weight.
- Unpacking and Inspection: Remove all shipping materials and inspect for transit damage. Verify all components are present.
- Water Connection Setup: Install water supply lines with proper shut-off valves. Pressure test connections to 150 PSI.
- Drain System Installation: Configure drain hose with approved standpipe installation and anti-siphon protection.
- Electrical Verification: Confirm dedicated 120V, 15A circuit with proper grounding. Verify voltage and polarity.
- Leveling and Alignment: Adjust leveling feet to achieve ±1° level tolerance. Verify stability under load.
- Initial System Test: Perform diagnostic cycle to verify all systems operational. Check for leaks and abnormal operation.
Technical Specifications
| Manufacturer | Maytag Corporation |
| Product Line | Commercial Grade Washers |
| Construction | Heavy-Duty Steel Cabinet |
| Capacity Range | 4.0 - 5.2 cu. ft. |
| Motor Type | Permanent Split Capacitor (PSC) |
| Control System | Electronic Control Board with Diagnostic Capability |
| Water Pressure Requirements | 20-120 PSI |
| Electrical Requirements | 120V, 60Hz, 15A Dedicated Circuit |
| Dimensions (HxWxD) | 43 x 27 x 28 inches |
| Shipping Weight | 205 lbs |
| Maximum Spin Speed | 1200 RPM |
| Water Consumption | 13.5 gallons per cycle (average) |
Warranty and Service Information
- Limited Warranty: 10 years on transmission, 1 year parts and labor
- Commercial Warranty: 90 days parts and labor for commercial use
- Extended Service: Available through authorized service providers
For technical support and warranty claims, contact Maytag Technical Assistance at 1-800-344-1274 or visit MaytagService.com
System Features
PowerWash® System
Maytag's PowerWash system uses high-pressure water jets and optimized wash plate movements to remove tough stains with powerful cleaning action.
Heavy Duty Cycle
Specifically designed for heavily soiled items with extended wash time, increased agitation, and extra rinse cycles for maximum cleaning performance.
Advanced Vibration Control
Intelligent suspension system with automatic balance detection and correction to minimize vibration and noise during operation.
Stainless Steel Wash Basket
Durable stainless steel construction resists chipping, rust, and corrosion while providing gentle fabric care and long-term reliability.
Quick Wash Option
Reduces cycle time to approximately 30 minutes for lightly soiled loads while maintaining effective cleaning performance.
Deep Fill Option
Allows manual addition of extra water for large or heavily soiled loads that require more thorough saturation and cleaning.
Control System Features
Electronic Controls
Microprocessor-based control system with cycle memory and diagnostic capability
LED Display
Digital display showing cycle status, time remaining, and diagnostic codes
Cycle Selection
Multiple cycle options including normal, heavy, delicate, quick wash, and rinse/spin
Temperature Control
Independent hot, warm, and cold water temperature selection for wash and rinse
Soil Level Adjustment
Adjustable wash intensity based on soil level from light to heavy
Diagnostic Mode
Built-in diagnostic system for troubleshooting and service verification
Diagnostic Troubleshooting
| Problem Description | Diagnostic Code | Recommended Service Procedure |
|---|---|---|
| No power to control system | F1 E1 | Check power supply, test outlet, verify door switch operation, inspect main control board |
| Water fill time-out error | F2 E1 | Test water inlet valve, check water pressure, inspect water level pressure switch |
| Drain time-out error | F3 E1 | Inspect drain pump, check drain hose for restrictions, test pump motor operation |
| Motor control fault | F5 E1 | Test motor windings, check motor capacitor, inspect drive belt and pulley system |
| Unbalanced load detection | F7 E1 | Verify proper load distribution, check suspension system, inspect shock absorbers |
| Temperature sensor fault | F8 E1 | Test thermistor resistance, inspect wiring harness, verify control board operation |
Common Error Code Definitions
- F1 E1: Main control board communication failure - Check control board connections and power supply
- F2 E1: Water fill system fault - Verify water supply and inlet valve operation
- F3 E1: Drain system malfunction - Inspect drain pump and hose routing
- F5 E1: Drive motor system error - Test motor and drive components
- F7 E1: Load balance system fault - Check suspension and load distribution
- F8 E1: Temperature system error - Verify thermistor and heating element operation
Technical Downloads
Current Technical Manuals
MVW7232HW
4.8 cu. ft. Top Load Washer
MVW7230HW
4.7 cu. ft. Heavy Duty Washer
MVW6200KW
4.3 cu. ft. Commercial Washer
MVW6520HW
5.2 cu. ft. Extra Capacity Washer
Legacy Model Documentation
MVWC565FW
5.0 cu. ft. Front Load Washer
MHW5630HW
4.3 cu. ft. High Efficiency Washer
MAV8600AW
4.0 cu. ft. Commercial Washer
MHW5500FW
4.5 cu. ft. Front Load Washer