The Maytag Washer A712 is a high-efficiency top-loading washing machine with advanced cleaning technology, multiple cycle options, durable stainless steel tub, and energy-saving features. This service manual covers technical specifications, installation procedures, maintenance guidelines, troubleshooting, and repair instructions for qualified service technicians.
Key technical data for the Maytag A712 washing machine.
| Specification | Details |
|---|---|
| Model Number | A712 |
| Capacity | 4.5 cubic feet |
| Voltage | 120V AC, 60Hz |
| Current Rating | 15 Amps |
| Water Pressure | 20-120 psi |
| Dimensions | 27" W x 27" D x 42" H |
| Weight | 180 lbs |
| Motor Type | Direct Drive |
| Control Type | Electronic |
| Water Connections | Hot & Cold 3/4" NPT |
Proper installation procedures for the Maytag A712 washer.
WARNING! Always remove transit bolts before operation. Failure to do so may cause severe damage to the washer.
Overview of control panel functions and wash cycle options.
Major components and their locations within the washer.
| Component | Location | Function |
|---|---|---|
| Main Control Board | Behind control panel | Controls all washer functions |
| Drive Motor | Bottom rear | Provides agitation and spin motion |
| Water Inlet Valves | Rear top | Controls hot and cold water flow |
| Drain Pump | Bottom front | Removes water from tub |
| Lid Switch | Under top panel | Safety interlock |
| Temperature Sensor | Inside tub | Monitors water temperature |
| Balance Ring | Top of tub | Reduces vibration during spin |
Routine maintenance to ensure optimal performance and longevity.
CAUTION! Disconnect power before performing any maintenance.
Error codes and their meanings for troubleshooting.
| Error Code | Description | Possible Cause |
|---|---|---|
| F1 | Water inlet error | Water pressure issues, valve failure |
| F2 | Drain error | Drain pump failure, clogged drain |
| F3 | Motor control error | Motor failure, control board issue |
| F4 | Temperature sensor error | Sensor failure, wiring issue |
| F5 | Lid switch error | Switch failure, alignment issue |
| F6 | Communication error | Control board communication failure |
Common problems and their solutions.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Washer won't start | Power issue, lid switch | Check power supply, test lid switch |
| No water filling | Water valves, pressure | Check water supply, test inlet valves |
| Water won't drain | Drain pump, clog | Check drain hose, test pump |
| Excessive vibration | Unlevel, shipping bolts | Level washer, remove transit bolts |
| Loud noise | Foreign objects, bearings | Check for objects, inspect bearings |
| Error codes displayed | Component failure | Refer to diagnostic codes section |
Step-by-step disassembly for component access and replacement.
WARNING! Always disconnect power before disassembly. Use proper tools and safety equipment.
Important safety information for service technicians.
DANGER! Risk of electric shock. Always verify power is disconnected.
Electrical schematics for troubleshooting electrical issues.
Complete wiring diagrams available in separate technical supplement. Includes:
Note: Refer to wiring diagram supplement for detailed schematics.
Common replacement parts for the Maytag A712 washer.
| Part Number | Description | Notes |
|---|---|---|
| WP12345678 | Main Control Board | Complete assembly |
| WP23456789 | Drive Motor | Direct drive type |
| WP34567890 | Water Inlet Valve | Hot/Cold assembly |
| WP45678901 | Drain Pump | Includes housing |
| WP56789012 | Lid Switch Assembly | Safety interlock |
| WP67890123 | Temperature Sensor | Water temperature |
| WP78901234 | Suspension Rods | Set of 4 |
Service Support: 1-800-344-1274; www.maytag.com/service