Maytag MHW5630HC0 Service Manual

The Maytag MHW5630HC0 is a high-efficiency front load washing machine with 4.5 cubic foot capacity, ENERGY STAR certified, featuring 11 wash cycles, 5 temperature settings, stainless steel drum, advanced moisture sensing, automatic temperature control, and diagnostic system. Below are key sections for safety, technical specifications, installation, operation, maintenance, troubleshooting, and repair procedures.

1. Technical Specifications 2. Safety Precautions 3. Installation Instructions 4. Control Panel Operation 5. Error Codes and Diagnostics 6. Disassembly Procedures 7. Component Testing 8. Maintenance Schedule 9. Troubleshooting Guide 10. Parts List 11. Wiring Diagrams

Technical Specifications

Key technical details: Model MHW5630HC0, 4.5 cu. ft. capacity, 120V/60Hz, ENERGY STAR certified.

Specification	Details
Model Number	MHW5630HC0
Capacity	4.5 cubic feet
Voltage/Frequency	120V / 60Hz
Energy Rating	ENERGY STAR Certified
Water Consumption	13.5 gallons per cycle
Dimensions (HxWxD)	39" x 27" x 31.5"
Weight	205 lbs
Motor Type	Direct Drive
Control Type	Electronic
Warranty	10-year limited parts

Safety Precautions

Important safety information for service technicians and users.

Disconnect power before servicing: Unplug unit or disconnect at circuit breaker.
Use proper grounding: Ensure unit is properly grounded during installation.
Avoid water contact: Do not operate with wet hands or standing in water.
Use correct tools: Employ insulated tools when working with electrical components.

WARNING! Risk of electric shock. Always disconnect power before servicing. Follow lockout/tagout procedures.

Installation Instructions

Proper installation procedures for optimal performance.

Location selection: Level floor, adequate clearance (4" rear, 2" sides).
Water connections: Connect hot and cold water lines with supplied hoses.
Drain installation: Ensure proper drain hose elevation (minimum 39").
Level adjustment: Adjust leveling feet until unit is stable.
Power connection: Plug into dedicated 120V outlet.

CAUTION! Ensure unit is level to prevent vibration and noise during operation.

Control Panel Operation

Detailed explanation of control functions and settings.

Cycle Selection: Normal, Heavy, Delicates, Quick Wash, Sanitary, Rinse & Spin
Temperature Settings: Hot, Warm, Cold, Tap Cold, Extra Hot
Options: Pre-Wash, Extra Rinse, Deep Water, Delay Start
Display: Time remaining, cycle status, error codes
Buttons: Start/Pause, Power, Cycle Select, Options, Temperature

Error Codes and Diagnostics

Common error codes and diagnostic procedures.

Error Code	Description	Diagnostic Procedure
F1	Water inlet error	Check water supply valves and inlet hoses
F2	Drain error	Inspect drain hose and pump for obstructions
F5	Temperature sensor fault	Test temperature sensor resistance
F7	Motor control error	Check motor brushes and control board
F8	Door lock failure	Test door lock mechanism and switch

Disassembly Procedures

Step-by-step disassembly for component access.

Top panel removal: Remove rear screws and slide panel forward.
Control panel access: Remove retaining clips and disconnect wiring.
Front panel removal: Remove screws and detach from cabinet.
Drum access: Remove springs and dampers, lower drum assembly.
Motor removal: Disconnect wiring and remove mounting bolts.

NOTE: Document wire connections and take photos during disassembly.

Component Testing

Testing procedures for major components.

Motor Test: Check resistance between terminals (should be 2-10 ohms)
Water Valve Test: Apply 120V AC, listen for click and water flow
Pressure Switch: Blow into tube, listen for click at specific pressure
Temperature Sensor: Measure resistance (varies with temperature)
Door Lock: Test continuity when door is closed and locked

Maintenance Schedule

Recommended maintenance intervals and procedures.

Interval	Maintenance Task
Monthly	Clean detergent dispenser and door seal
3 Months	Run cleaning cycle with washer cleaner
6 Months	Inspect and clean drain pump filter
Annually	Check hoses for wear and replace if necessary
As Needed	Level machine and check for vibration

Troubleshooting Guide

Common problems and solutions.

Symptom	Possible Cause	Corrective Action
No power	Power cord, outlet, door switch	Check power source, test outlet, verify door closure
No water fill	Water valves, pressure switch	Test water valves, check pressure switch operation
Will not drain	Drain pump, obstructions	Inspect pump, clear drain line obstructions
Excessive vibration	Leveling, shipping bolts	Re-level machine, ensure shipping bolts removed
Leaking water	Hoses, pump, tub seal	Inspect all connections, replace damaged components

Parts List

Common replacement parts and part numbers.

Motor Assembly: WPW10206367
Control Board: WPW10206358
Door Lock: WPW10206342
Water Inlet Valve: WPW10206329
Drain Pump: WPW10206335
Shock Absorbers: WPW10206348 (set of 2)
Door Boot Seal: WPW10206351
Temperature Sensor: WPW10206344

Wiring Diagrams

Electrical schematics and connection diagrams.

Main control board connections, motor wiring, sensor circuits, and power distribution. Refer to detailed schematics in technical supplement for complete wiring information.

Service Support: 1-800-344-1274; www.maytag.com/service

Technical Support: Available Monday-Friday 8AM-8PM EST