Parts Overview
Safety First:
- Always disconnect power before replacing parts
- Use proper safety equipment
- Follow manufacturer specifications
- Keep work area clean and organized
- Dispose of old parts properly
Main Components
- Motor Assembly: Direct drive motor with electronic controls
- Transmission: Gear system for wash and spin cycles
- Water Inlet Valve: Controls hot and cold water flow
- Drain Pump: Removes water from the tub
- Suspension System: Shock absorbers and springs
- Control Board: Electronic control center
- Tub and Drum: Stainless steel wash basket
- Door Assembly: Glass door with lock mechanism
Common Replacement Parts
| Part Number | WPW10305657 |
| Part Name | Drive Motor |
| Compatibility | All Bravos XL Models |
| Water Inlet Valve | WPW10205477 |
| Drain Pump | WPW10205466 |
| Door Lock | WPW10205472 |
| Shock Absorber | WPW10205459 |
| Control Board | WPW10305649 |
| Drive Belt | WPW10205463 |
| Tub Seal | WPW10205471 |
| Temperature Sensor | WPW10205468 |
Tools Required for Parts Replacement
- Basic Toolkit: Screwdrivers, pliers, wrenches
- Multimeter: For electrical testing
- Putty Knife: For gasket removal
- Nut Drivers: Various sizes
- Safety Gloves: Protection during disassembly
Parts Installation Guide
Drive Motor Replacement
Remove rear panel, disconnect electrical connections, remove mounting bolts, install new motor ensuring proper alignment, reconnect wiring.
Water Inlet Valve
Disconnect water supply, remove rear access panel, disconnect wiring harness, remove mounting screws, install new valve with new seals.
Drain Pump Installation
Access front service panel, disconnect drain hoses, remove mounting clips, install new pump ensuring proper hose connections and seals.
Shock Absorber Replacement
Lay washer on its back, remove base panel, compress and remove old shocks, install new shocks with proper mounting hardware.
Control Board
Remove console cover, document wire connections, disconnect all connectors, remove mounting screws, install new board and reconnect all wires.
Door Lock Mechanism
Remove door boot clamp, access lock assembly, disconnect wiring, remove mounting screws, install new lock and test operation.
Installation Tips
Document Connections
Take photos before disconnecting wires for proper reassembly
Use Genuine Parts
Always use Maytag genuine replacement parts for best performance
Check Alignment
Ensure all moving parts are properly aligned during installation
Test Before Reassembly
Test component operation before final reassembly
Torque Specifications
Follow manufacturer torque specifications for all fasteners
Safety Check
Perform complete safety check before returning to service
Parts Troubleshooting
| Symptom | Possible Faulty Part | Diagnosis Procedure |
|---|---|---|
| Washer won't start | Door lock, Control board | Check door lock operation, test control board power |
| No water filling | Water inlet valve, Pressure switch | Test valve operation, check water pressure |
| Water not draining | Drain pump, Drain hose | Check pump operation, inspect hose for clogs |
| Excessive vibration | Shock absorbers, Springs | Inspect suspension system, check for wear |
| Motor not running | Drive motor, Motor control | Test motor windings, check control signals |
| Leaking water | Tub seal, Hoses, Pump seal | Inspect all seals and connections for leaks |
Diagnostic Error Codes
- F1: Water fill time exceeded - Check water supply and inlet valve
- F2: Drain time exceeded - Check drain pump and hose
- F3: Heater fault - Check heating element and thermostat
- F4: Motor triac fault - Check motor and control board
- F5: Stuck key - Check control panel for stuck buttons
- F6: Communication error - Check wiring between boards
Parts Ordering Information
Current Bravos XL Parts
Drive System Parts
Motors, belts, pulleys
Water System Parts
Valves, pumps, hoses
Electronic Parts
Boards, sensors, displays
Mechanical Parts
Seals, bearings, hardware
Service Documentation
Exploded Views
Detailed parts diagrams
Wiring Diagrams
Electrical schematics
Service Manual
Complete repair guide
Technical Bulletins
Service updates