Installation Guide
Tools Needed:
- Adjustable wrench
- Level
- Screwdrivers (flat and Phillips)
- Pliers
- 4-inch duct clamp
- Tape measure
Step-by-Step Installation
- Choose Installation Location: Select a location with proper ventilation and adequate clearance on a solid, level floor.
- Remove Shipping Materials: Remove all shipping bolts and packaging materials from the dryer.
- Gas Connection (Gas Models): Connect gas line using approved flexible connector. Check for leaks with soap solution.
- Electrical Connection: Connect to properly grounded 120V, 60Hz outlet for electric models or 120V for gas models ignition system.
- Ventilation System: Install 4-inch diameter metal ductwork with minimal bends. Ensure proper exterior venting.
- Level the Dryer: Adjust the leveling legs to ensure the dryer is level from front to back and side to side.
- Test Run: Run the dryer through a complete cycle to check for proper operation and ventilation.
Specifications
| Model Series | MEDC400XW |
| Type | Electric/Gas Dryer |
| Color | White |
| Capacity | 7.4 cu. ft. |
| Noise Level | 65 dB |
| Control Type | Electronic Controls with LED Display |
| Energy Rating | ENERGY STAR® Certified |
| Power Requirements (Electric) | 240V, 30A |
| Power Requirements (Gas) | 120V, 15A (Ignition System) |
| Dimensions (HxWxD) | 43 x 29 x 29 inches |
| Weight | 125 lbs |
| Drum Material | Stainless Steel |
Warranty Information
- Full Warranty: 1 year parts and labor
- Motor Warranty: 10 years on drive motor
- Drum Warranty: Lifetime limited warranty
- Additional Coverage: Optional extended warranty available
For warranty service, contact Maytag Customer Service at 1-800-344-1274 or visit Maytag.com
Key Features
Advanced Moisture Sensing
Automatically detects moisture levels and adjusts drying time accordingly, preventing over-drying and saving energy while protecting fabrics.
XL Capacity
7.4 cubic foot capacity allows for drying larger loads, including comforters and bulky items, reducing the number of cycles needed.
Wrinkle Guard™ Option
Periodically tumbles clothes after the cycle ends to help prevent wrinkles from setting in when you can't unload immediately.
Steam Refresh Cycle
Uses steam to remove wrinkles and odors from clothes that have been sitting in the dryer or closet, refreshing them without washing.
Quick Dry Cycle
Dries small loads quickly by increasing temperature and airflow, perfect for when you need specific items in a hurry.
Stainless Steel Drum
Durable stainless steel construction resists chipping and rusting, providing long-lasting performance and gentle fabric care.
Drying Cycles Explained
Auto Dry
Automatically senses moisture and shuts off when clothes are dry
Timed Dry
Manual time setting for specific drying durations
Wrinkle Control
Periodic tumbling after cycle to prevent wrinkles
Steam Refresh
Uses steam to remove wrinkles and refresh clothes
Quick Dry
Rapid drying for small, lightly damp loads
Air Fluff
No heat cycle for fluffing pillows or refreshing items
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Dryer won't start | Power issue, door not closed properly, start button not held | Check power supply, ensure door is latched, hold start button for 3 seconds |
| No heat | Thermal fuse blown, heating element failure, gas supply issue | Check thermal fuse, test heating element, verify gas supply (gas models) |
| Clothes taking too long to dry | Clogged lint filter, restricted venting, overloading | Clean lint filter, check vent system, reduce load size |
| Unusual noises | Foreign objects in drum, worn rollers or bearings | Check for foreign objects, inspect drum rollers and bearings |
| Dryer overheats | Restricted airflow, faulty thermostat, clogged vent | Clean lint filter and vent system, check thermostats |
| Error codes displayed | Sensor issues, control board problems | Refer to error code chart, reset dryer, contact service if persistent |
Error Codes
- F1: Control board failure - Reset dryer, contact service
- F2: Motor triac error - Check drive motor, control board
- F3: Thermistor open - Temperature sensor issue
- F4: Thermistor short - Temperature sensor failure
- F5: Thermal cutoff open - Overheating protection activated
- F7: Heater relay error - Heating system control issue
- F8: Moisture sensor error - Dryness detection system fault
Manual Downloads
Current Model Manuals
MEDC400XW
7.4 cu. ft. Electric Dryer
MEDC400YW
7.4 cu. ft. Electric Dryer
MEDC400XG
7.4 cu. ft. Gas Dryer
MEDC400YG
7.4 cu. ft. Gas Dryer
Popular Previous Models
MEDX500XW
7.3 cu. ft. Electric Dryer
MEDX500XG
7.3 cu. ft. Gas Dryer
MEDB835DW
7.0 cu. ft. Electric Dryer
MEDB835DG
7.0 cu. ft. Gas Dryer