Maytag A112 Repair Manual

The Maytag A112 is a classic top-loading washing machine known for its durability and reliability. This repair manual covers essential maintenance, troubleshooting, and repair procedures for the A112 model. Below are key sections covering safety precautions, common issues, disassembly instructions, replacement parts, and maintenance guidelines.

1. Safety Precautions 2. Model Specifications 3. Common Problems 4. Disassembly Guide 5. Replacement Parts 6. Electrical System 7. Mechanical Components 8. Maintenance Schedule 9. Troubleshooting Guide 10. Warranty Information 11. Technical Support

Safety Precautions

Before attempting any repairs, ensure proper safety measures are followed.

Safety Measure	Description
Power Disconnection	Always unplug machine from electrical outlet before servicing
Water Supply	Turn off water supply valves before working on water connections
Proper Tools	Use insulated tools when working with electrical components
Lifting Safety	Use proper lifting techniques; machine weighs approximately 150 lbs
Component Handling	Allow machine to cool if recently used; avoid hot surfaces

Model Specifications

Model: Maytag A112
Type: Top-loading automatic washer
Capacity: 12 lbs dry laundry
Motor: 1/2 HP induction motor
Voltage: 120V AC, 60Hz
Water Connections: Hot and cold water inlets
Dimensions: 27" W x 27" D x 42" H
Weight: 150 lbs

Common Problems

Frequent issues encountered with Maytag A112 washers.

Machine won't start or power on
Water not filling or overfilling
Drum not spinning or agitating
Excessive vibration during operation
Water leakage from bottom
Unusual noises during cycle
Drainage problems

WARNING! Always disconnect power before troubleshooting electrical issues.

Disassembly Guide

Step-by-step instructions for accessing internal components.

Remove top panel: Insert putty knife between top and front panel, release clips
Remove control panel: Unscrew mounting screws, disconnect wiring harnesses
Remove front panel: Remove screws along sides and bottom
Access tub: Remove agitator and lift out
Remove pump: Disconnect hoses and mounting bolts
Access motor: Remove drive belt and mounting bolts

CAUTION! Label all wires and take photos during disassembly for reassembly reference.

Replacement Parts

Part Number	Description	Common Use
MAY-112-001	Drive Motor	Motor replacement
MAY-112-002	Water Pump Assembly	Drainage issues
MAY-112-003	Timer Control	Cycle problems
MAY-112-004	Lid Switch	Machine won't start
MAY-112-005	Transmission	Agitation/spin issues
MAY-112-006	Water Inlet Valve	Filling problems

Electrical System

Electrical components and testing procedures.

Main Components: Timer, Motor, Lid Switch, Water Level Switch, Fill Valve

Testing Procedures: Use multimeter to check continuity and voltage. Timer contacts should show continuity when engaged. Lid switch should open circuit when lid is raised. Motor windings should show specified resistance values.

Mechanical Components

Key mechanical parts and maintenance requirements.

Transmission: Lubricate annually with approved grease
Drive Belt: Check tension and wear every 6 months
Motor Coupling: Inspect for cracks or wear
Suspension Springs: Check for even tension
Dampers: Replace if leaking or damaged

Tip: Regular maintenance extends machine lifespan and prevents major repairs.

Maintenance Schedule

Recommended maintenance intervals for optimal performance.

Monthly: Clean lint filter, inspect hoses
Quarterly: Run cleaning cycle with washer cleaner
Annually: Inspect drive belt, check motor brushes
Every 2 years: Replace water inlet hoses
Every 5 years: Professional inspection recommended

Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
Machine won't start	Lid switch, power cord, timer	Check lid switch operation; verify power supply; test timer
No water filling	Water valves, pressure switch	Check water supply; test inlet valves; verify pressure switch
Not spinning	Drive belt, motor coupling	Inspect belt for wear; check motor coupling; test motor
Water leakage	Hoses, pump, tub seal	Inspect all hoses; check pump seal; examine tub gasket
Loud noises	Bearings, foreign objects	Check tub bearings; remove objects from drum; inspect motor

Warranty Information

Original warranty: 10 years on transmission, 1 year parts and labor. Current repair warranty: 90 days on replaced parts. Keep original purchase receipt for warranty claims.

Technical Support

For technical assistance, contact Maytag Customer Service at 1-800-344-1274 or visit www.maytag.com. Provide model number A112 and serial number when contacting support. Authorized service centers available nationwide.